DMM2 / ME22007Configuration B

Snowmobile track drive shaft: FBD, SFD, BMD and torque

Configuration B, worked as a method you can repeat when the transmission changes.

Assumption, confirm on Moodle Q&A. Config B geometry is taken from brief Fig 3.2 with B and C swapped. All loads are first-pass example numbers from the group's loads spreadsheet.

1The idea in one line

The shaft is a simply supported beam with point loads at the component centrelines. The loads are not in one plane, so split them into the horizontal and vertical planes, solve each as a 2D beam, then recombine.

Why this works: bending in one plane does not care about forces in the perpendicular plane. Each plane obeys its own ΣF = 0 and ΣM = 0, and the stresses only meet again at the cross-section, where the two moments combine as vectors.

Pin A and pin B support
Loads at centrelines
Two planes, then recombine

2Layout

Shaft along x from bearing A. A and B are bearings, idealised as simple (pin) supports. T1 and T2 are the track sprockets, C is the driven chain sprocket. D is the drive sprocket on the motor, above and forward of C, with the line of centres at 30° to horizontal. Sprocket sizes are schematic.

50mm300mm50mm60mm460mm overallT1 track sprocketT2 track sprocketC chain sprocket290mm PCD290mm PCDbearing Abearing BABT1T2x = 0x = 50mmx = 350mmx = 400mmx = 460mm
End view (looking along the shaft). Forward = right.T (290mm PCD)CDdrive sprocket(motor)30°F_C = 2122N1838N forward1061N uptrack pull 720N each, rearward(tight bottom run)

Loads orange arrows, applied at the centreline of each sprocket.

Reactions blue arrows, at the bearings A and B.

The chain pulls C along the line towards D, so F_C splits into a forward part (F_C cos30) and an upward part (F_C sin30). The tight bottom run of each track pulls its sprocket rearward, horizontally.

3Horizontal plane: FBD, then SFD and BMD

Positive = forward. Every arrow is drawn in its actual direction. Under the FBD, the SFD and BMD share the same x axis (dashed station lines).

AT1T2CBF_T = 720N rearwardF_T = 720N rearwardF_C cos30 = 1838N forwardR_Ah = +574NR_Bh = −972N (rearward)Horizontal plane (plan view, forward = up the page, positive forward)SFD V(x)+574.2N−145.8N−865.8N+972.2NxNBMD M(x)+28.7Nm−15.0Nm−58.3NmxNm
R_Ah + R_Bh = 720 + 720 − 1838 = −398N (574 − 972 = −398N)
ΣF_h = 574 − 720 − 720 + 1838 − 972 = 0 (checks: 0)
ΣM_B(h) = 0 (checks: 0)

4Vertical plane: FBD, then SFD and BMD

Positive = up. Only C loads this plane, with F_C sin30 = 1061N up, so both bearings must pull the shaft down.

AT1T2CBF_C sin30 = 1061N upR_Av = −138N (down)R_Bv = −923N (down)Vertical plane (side view, positive = up)SFD V(x)−138.4N−138.4N−138.4N+922.6NxNBMD M(x)−6.9Nm−48.4Nm−55.4NmxNm
R_Av + R_Bv = 1061N up − 1061N (−138 − 923 = −1061N)
ΣF_v = −138 + 1061 − 923 = 0 (checks: 0)
ΣM_B(v) = 0 (checks: 0)

Arrow lengths are indicative, the 138N arrow is lengthened so the head stays visible. Read the labels, not the lengths.

5How to read the SFD and BMD

Between point loads the shear is constant, so the moment is a straight line whose slope equals that shear. At each point load the shear jumps by the load, and the moment line changes slope. The moment returns to 0 at both pins.

PlaneA to T1T1 to T2T2 to CC to B
Horizontal SFD+574.2N−145.8N−865.8N+972.2N
Vertical SFD−138.4N−138.4N−138.4N+922.6N
MomentAT1T2CB
Horizontal M_h0+28.7Nm−15.0Nm−58.3Nm0
Vertical M_v0−6.9Nm−48.4Nm−55.4Nm0

6Resultant bending moment

The two planes are perpendicular, so the two moments at a section are perpendicular vectors and add by Pythagoras. A shaft does not care which plane it bends in, only how big the total moment is.

M = √(M_h² + M_v²)
SectionM_hM_vM
T128.7Nm6.9Nm29.5Nm
T215.0Nm48.4Nm50.7Nm
C (critical)58.3Nm55.4Nm80.4Nm
29.5NmT150.7NmT280.4NmCM = sqrt(Mh² + Mv²)critical section

Magnitudes only: the signs drop out because the square removes them.

7Torque diagram

AT1T2CB0T/2 = 104.4NmT = 208.8Nm0T enters at CT(x) in Nm

Torque T enters the shaft at C from the chain. It travels towards the track sprockets and leaves through them. At T2 half of it is taken out by that track, and the other half T/2 carries on to T1, where it leaves. So the shaft carries T between T2 and C, T/2 between T1 and T2, and nothing outside the sprockets. A to T1 and C to B carry no torque.

C to T2: T = 208.8Nm T2 to T1: T/2 = 104.4Nm elsewhere: 0

8Where the numbers come from

First-pass examples. These values come from the group's loads spreadsheet. The method is what matters, and the numbers change when the transmission is picked.
n = v / (π D_T) = 13.89m/s / (π × 0.290m) ≈ 915RPM at 50km/h
T = P / ω = 20kW / 95.8rad/s ≈ 208.8Nm
F_T = (T/2) / (D_T/2) = 104.4Nm / 0.145m = 720N
F_C = T / (D_C/2) = 208.8Nm / 0.0984m ≈ 2122N
F_C cos30 = 1838N forward F_C sin30 = 1061N up

9Then what

Reactions. Take moments about one bearing, then ΣF for the other, in each plane separately. Confirm both ΣF and ΣM close to 0.

SFD and BMD per plane. Walk along the beam, step the shear at each load, integrate to get the moment, and check it returns to 0 at B.

Resultant M. Combine at each section with M = √(M_h² + M_v²). The largest is at C, 80.4Nm.

Torque. Trace T from where it enters (C) to where it leaves (T1 and T2). The shaft carries T, T/2 or 0 in each segment.

Combined stress at T1, T2 and C.

σ = 32M / (π d³) τ = 16T / (π d³)
σ' = √(σ² + 3τ²) compared with σy / SF

Pick d so that σ' is below σy/SF at the worst of the three sections. C has the largest M and the full T, so it is the likely governor, but check T2 as well.

Stress concentration. Multiply the nominal stress by Kt at shoulders and keyway ends. The nominal sections above are only the start, the local peak at a shoulder near C can govern the design.

10Check yourself

Why does the track pull the sprocket rearward?

The drive tension sits in the tight bottom run of the track, the run that pushes the machine forward by reacting against the ground. That run pulls on the lower edge of each sprocket in the direction the track wants to travel relative to the snow, which is rearward on the sprocket. The slack top run carries almost nothing, so the net sprocket load is one horizontal force of 720N each, rearward.

Why must the peak bending moment sit at a load point?

Between point loads the shear V is constant. Since dM/dx = V, the moment is a straight line there. A straight line has its extremes at its ends, and the ends of each segment are the load points or the supports. So the maximum can only be at a load point, which is why you only evaluate A, T1, T2, C and B.

Why does config B beat config A in bending?

In config B, C sits inside the span between the bearings, so the two bearings share the chain load and the moment peaks at C with a modest value. In config A, C is on a 60mm overhang past bearing B. The overhang acts like a lever, the load is carried mostly by the near bearing with a reaction bigger than the load, and the moment at B grows with the overhang length. Bringing C inside the span removes that lever arm.